TRF7970A
SLOS743K – AUGUST 2011 – REVISED APRIL 2014
Table 6-7. Coding of the ISO Control Register For RFID Mode (B5 = 0) (continued)
www.ti.com
Iso_4
0
0
0
Iso_3
1
1
1
Iso_2
0
0
1
Iso_1
1
1
0
Iso_0
0
1
0
Protocol
ISO14443 A high bit rate 424 kbps
ISO14443 A high bit rate 848 kbps
ISO14443B, bit rate 106 kbps
Remarks
RX bit rate when TX rate
0
1
1
0
1
ISO14443 B high bit rate 212 kbps
different from RX rate (see
register 0x03)
0
0
1
1
1
1
1
1
0
0
1
1
1
1
0
1
0
0
1
1
1
0
1
1
0
1
1
0
0
1
ISO14443 B high bit rate 424 kbps
ISO14443 B high bit rate 848 kbps
Reserved
Reserved
FeliCa 212 kbps
FeliCa 424 kbps
Table 6-8. Coding of the ISO Control Register For NFC
Mode (B5 = 1, B2 = 0) or Card Emulation (B5 = 1,
B2 = 1)
Iso_1
0
0
1
1
Iso_0
0
1
0
1
NFC (B5 = 1, B2 = 0)
N/A
106 kbps
212 kbps
424 kbps
Card Emulation
(B5 = 1, B2 = 1)
ISO14443A
ISO14443B
N/A
N/A
6.5.1
Received Signal Strength Indicator (RSSI)
The TRF7970A incorporates in total three independent RSSI building blocks: Internal Main RSSI, Internal
Auxiliary RSSI, and External RSSI. The internal RSSI blocks are measuring the amplitude of the
subcarrier signal; the External RSSI block measures the amplitude of the RF carrier signal at the receiver
input.
6.5.1.1
Internal RSSI – Main and Auxiliary Receivers
Each receiver path has its own RSSI block to measure the envelope of the demodulated RF signal
(subcarrier). Internal Main RSSI and Internal Auxiliary RSSI are identical however connected to different
RF input pins. The Internal RSSI is intended for diagnostic purposes to set the correct RX path conditions.
The Internal RSSI values can be used to adjust the RX gain settings or decide which RX path (Main or
Auxiliary) provides the greater amplitude and hence to decide if the MUX may need to be reprogrammed
to swap the RX input signal. The measuring system latches the peak value, so the RSSI level can be read
after the end of each receive packet. The RSSI register values are reset with every transmission (TX) by
the reader. This ensures an updated RSSI measurement for each new tag response.
The Internal RSSI has 7 steps (3 bit) with a typical increment of approximately 4 dB. The operating range
is between 600 mV PP and 4.2 V PP with a typical step size of approximately 600 mV. Both Internal Main
and Internal Auxiliary RSSI values are stored in the RSSI Levels and Oscillator Status register (0x0F). The
nominal relationship between the input RF peak level and the RSSI value is shown in Figure 6-5 .
24
Detailed Description
Submit Documentation Feedback
Product Folder Links: TRF7970A
Copyright ? 2011–2014, Texas Instruments Incorporated
相关PDF资料
TRM-418-LT TRANSCEIVER RF 418MHZ LT SERIES
TRM-900-NT RF TXRX 915MHZ NT SERIES
TRX08GVP2540 TXRX OPT SCFF 8.5GB/S 850NM
TS-320240BRNO TCH PANEL 140X104 RESISTIVE MONO
TS-TFT3.5Z TOUCH PANEL 140X1.4.0 TFT
TS3-75B3 SENSOR THERMAL MOXIE NTC 75C
TSL26711FN IC PROXIMITY DETECTOR 6-DFN
TSOP57238TT1 IC IR RCVR MODULE 38KHZ
相关代理商/技术参数
TRF7970ARHBR 功能描述:IC RFID/NFC AFE 13.56MHZ 32QFN RoHS:是 类别:RF/IF 和 RFID >> RFID IC 系列:- 其它有关文件:CR14 View All Specifications 标准包装:1 系列:- RF 型:收发器 频率:13.56MHz 特点:ISO14443-B 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SO 包装:Digi-Reel® 其它名称:497-5719-6
TRF7970ARHBT 功能描述:IC RFID/NFC AFE 13.56MHZ 32QFN RoHS:是 类别:RF/IF 和 RFID >> RFID IC 系列:- 其它有关文件:CR14 View All Specifications 标准包装:1 系列:- RF 型:收发器 频率:13.56MHz 特点:ISO14443-B 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SO 包装:Digi-Reel® 其它名称:497-5719-6
TRF7970ATB 功能描述:RFID应答器 TRF7970A Target Brd RoHS:否 制造商:Murata 存储容量:512 bit 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
TRF79A6AA17LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA18LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA19LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA20LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA21LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)